This shows you the differences between two versions of the page.
|
courses:el3203_2014:doublebalancedmixer [2014/02/06 03:58] |
courses:el3203_2014:doublebalancedmixer [2014/02/06 03:58] (current) |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== Double balanced mixer ====== | ||
| + | ===== Goals ===== | ||
| + | * Understand the operation of a double balanced mixer | ||
| + | |||
| + | {{mixer.png?600}} | ||
| + | |||
| + | * The above figure shows the mixer designed in the previous experiment. Ideally a mixer fed with V<sub>RF</sub> and V<sub>LO</sub> should have only product of these two components at the output. i.e the output should be zero if either of V<sub>RF</sub> or V<sub>LO</sub> is zero. But, as seen earlier, with V<sub>RF</sub>=0, the above mixer still generates an output proportional to V<sub>LO</sub>(LO feedthrough). Such a mixer is known as a single balanced mixer. | ||
| + | |||
| + | * LO feedthrough can be eliminated as shown in the circuit below by having two mixers driven by +v<sub>RF</sub> and -v<sub>RF</sub> and taking the difference between them. It can be seen by inspection that, when v<sub>RF</sub>=0, the sum of currents through Q<sub>1</sub> and Q<sub>2a</sub> is a constant as is the sum of currents through Q<sub>2</sub> and Q<sub>1a</sub>. This is a double balanced mixer. | ||
| + | |||
| + | {{:courses:ec330_2008:mixer1.png?600}} | ||
| + | |||
| + | * The above circuit is available in the form of an IC-the MC1496 double balanced modulator. Its internal schematic is shown below. Most of the circuitry including the biasing arrangements are inside the IC. Only R<sub>E</sub>, the load resistors, and the bias current setting resistor need to be connected externally. Compared to the circuit above, the bottom two transistors and their degenerating resistors are arranged as a differential pair inside the MC1496 integrated circuit. | ||
| + | |||
| + | {{:courses:ec330_2008:mixer2.png?500}} | ||
| + | |||
| + | ===== To be done before the lab session ===== | ||
| + | * Go through the [[http://www.ee.iitm.ac.in/~nagendra/EC330/200901/lectures/ec330-mixer2/ec330-mixer2.swf|lecture on double balanced mixers]]. | ||
| + | * Design a double balanced mixer around the MC1496 IC. Use a 12V supply and 1mA current through the bias branch. The mixer should be able to take in an RF input peak of 1V and have a conversion gain(ratio of the //sinusoidal component// at f<sub>RF</sub>+f<sub>LO</sub> OR f<sub>RF</sub>-f<sub>LO</sub> at the differential output to the amplitude of the //input sinusoid//) of 4. | ||
| + | |||
| + | ===== To be done in the lab session ===== | ||
| + | Verify the circuit designed above: | ||
| + | * Take V<sub>outp</sub> or V<sub>outm</sub> as the output. | ||
| + | * Drive the input with a low frequency v<sub>RF</sub>(~ 1kHz) and a high frequency v<sub>LO</sub>(~10kHz) and observe the output. You can use the oscillator designed in the previous experiment as the 10kHz source. | ||
| + | * Verify that the outputs are as expected. | ||
| + | |||
| + | {{diff2se.png?500}} | ||
| + | |||
| + | * Build the differential to single ended converter shown above and drive it from the mixer. Choose appropriate supply voltages for the opamp. | ||
| + | * Drive the mixer with a low frequency v<sub>RF</sub> and a high frequency v<sub>LO</sub> and observe the output. | ||
| + | * Drive the mixer with a v<sub>RF</sub> and v<sub>LO</sub> at close by, but not identical frequencies and observe the low frequency(f<sub>RF</sub>-f<sub>LO</sub>) output. For filtering out the high frequency component, use a capacitor of appropriate value across R<sub>L</sub>(both of them) which will short it out at high frequencies. Filtering will be a lot easier if you choose a higher f<sub>LO</sub>, say 25kHz or 50kHz, and a difference frequency around 1kHz. | ||
| + | * Remove the RF input and observe the output. | ||
| + | * Remove the LO input and observe the output. | ||
| + | |||
| + | ===== Applications ===== | ||
| + | * This circuit is very commonly used for frequency translation in radio transmitters and receivers. | ||
| + | |||
| + | ===== Something to try on your own ===== | ||
| + | * Drive the lower input with audio, say from your computer or digital player. Drive the LO input with a sinusoid in the AM band(0.5-1.5MHz). You should be able to use an AM radio placed close by to receive the transmitted audio. You can use a short wire connected to the output node as an antenna. | ||